Addressable RGB LED Strip Light Controller
SP002E 3 key mini micro rgb controller
- DC5V 12V 24V
- Connector: 4-pin flat female jack, 5.5mm DC femal jack, 2-pin wire connector, USB connector
- Easily change the 19 dynamic modes, 5-speed levels, and 5 brightness levels
LED Dream-Color 14 key RF remote controller
- DC5~24V
- 358 different light effects covering the effects of the market for all symphony controller mode
- Program any combination of 16 and automatically play
- Maximum number of control points: 2048 pixels
- Max remote control distance: 30 meters
- For programmable LED strips like WS2811 WS2812B LED strip
24 Key infrared IR Remote Controller for WS2812 LED Strip
- DC5V
- 16 different colored buttons and 5 different light pattern functions: Static / Flash / Strobe / Fade / Smooth
- 16 classes static mode mim control
- 16 speed control in Flash / Strobe / Fade-change / RGB Smooth-change
- Great for addressable LED strip light like WS2812b LED strip
- Control range: 10cm – 500cm RGB LED strips
5v 12v 8 key 133 RF remote controller
- DC5V 12V
- For WS2811 1903 WS2801 LPD8806 LED strip, modules, string Lights
- Output: Two groups SPI signal
- Come with 133 different light change patterns
- Length setup function
- A lot of programs to chose
- Memory function
K-8000L 8 ports offline SD card TTL DMX512 RGB LED Strip Controller
- 32 to 65536 degree gray level control, Gamma correction
- Support various point, line and panel light source, special pattern shapes
- 8 output ports with each port can support up to 512/1024 pixels (DMX protocol up to 512 pixels)
- Playback content is stored in SD card which store up to 32 files, SD card capacity 128MB-32GB
- The controller can be used in a single unit or in multiple cascades. The cascade uses optical isolation: anti-interference, better stability, and cascading distance between the two units is up to 150 meters if using 0.5mm2 copper power cord
- Support load lamp is 4 channels (RGBW) pixels, or split into single channel pixels
- Enhanced 485 TTL and 485 differential (DMX) signal output
- The controller has 16 built-in effects (the internal control default chip is 1903)
K-1000C offline RGBW LED pixel controller with SD Card
- 32 to 65536 degree gray level control, Gamma correction procession handle
- Support various point, line and panel light source, special pattern shapes
- One output port can support up to 512 / 2048 pixels(DMX protocol up to 512 pixels)
- Playback content is stored in SD card which store up to 32 files, SD card capacity 128MB-32GB
- The controller can be used in a single unit or in multiple cascades. The cascade uses optical isolation: anti-interference, better stability, and cascading distance between the two units is up to 150 meters if using 0.5mm2 copper power cord
- The controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, this is more flexible and convenient
- For DMX lighting IC, the controller comes with write address function; In addition, with use of our 2016 LedEdit-K V3.26 or later edition can make one key write address function setting
- Support load lamp is 4 channels (RGBW) pixels, or split into single channel point pixels
- Enhanced 485 TTL and 485 differential (DMX) signal output
- The controller has 22 built-in effects for test
H803TC Online Offline DMX Master RGB LED Strip Controller
- H803TC can work with PC(online mode), SD card(offline mode), or DMX console
- H803TC drives maximum of 170000 pixels, 2 ports control maximum of 255 slave controllers
- Slave controllers include H802RA and H801RC
- You can set the address for DMX512 chips with H803TCH803TC transmits data based on Ethernet Protocol
- Use four buttons or PC to switch files, set play mode, speed and brightness
- SD card supports FAT32, FAT16 format, maximum capacity is 64G bytes, stores up to 64 DAT files
- H803TC supports below driver ICs:
LPD6803, LPD8806, LPD1882, LPD1889, LPD6812, LPD1883, LPD1886, DMX512, HDMX, APA102, MY9221, DZ2809, SM16716, SM16711, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, WS2801, WS2803, WS2811, WS2812, INK1003, TM1812, TM1809, TM1804, TM1803, TM1913, TM1914, TM1926, TM1829, TM190, TM1814, BS0901, BS0902, BS0825, BS0815, LY6620, BS0825, LD1510, LD1512, D1530,LD1532, TLS3001, TLS3002, DM412, DM413, DM114, DM115, DM13C, DM134, DM135, DM136, MBI6023, MBI6024, MBI5001, MBI5168, MBI5016, MBI5026, MBI5027, 74HC595, 6B595, TB62726, TB62706, ST2221A, ST2221C, XLT5026, ZQL9712, ZQL9712HV, HEF4094, A8012, etc.
Note: H803TC can support more than the chips listed above(some chips have the same sequence diagram, for example: UCS512, WS2821 and DMX512 have the same protocol. UCS2903 has the same sequence diagram with UCS1903, so H803TC supports them all).
H803TV online Madrix master controller DVI/HDMI interface for 3D and music effect
- Four network interfaces drive maximum 400000 pixels
- It supports dual-monitor mode, multi-monitor extension mode and duplication mode
- Four ports are separated and configured individually, which means four ports can drive different chips. Compatible with Madrix software, display whatever displays on your screen
- Connect video splitter to control part of the video section by section
- Support the following resolutions: 1024×768, 1280×720, 1280×960, 1280×1024, 1360×765, 1360×1020, 1600×900, 1600×1200
- Use the autorun USB to transmit and control data, which is applied to both 32-bit and 64-bit operating systems
- Auxiliary slave controller is H801RA, H802RA and H801RC
- Data is transmitted based on standard Ethernet protocol from H803TV to slave controller and the transmission distance is up to 100 meters
- Screen refresh frequency is recommended to be 60HZ.
H801RC Offline Online 8 ports RGB LED Light Slave Controller
- H801RC can be connected to computer newtwork, H803TC or H803TV master controller, switch or photoelectric converter
- 8 output ports drive maximum 8192 pixels
- High synchronization performance, the transmission of adjacent slave controller delays within 400ns
- Good control effect and grayscale level is under precisely control
- Far transmission distance. Signal transmitted based on standard Ethernet protocol and the nominal transmission distance is 100 meters
- The clock scanning frequency is adjustable within 100K to 50M Hz
- Offline auxiliary software is “LED Build Software”, online auxiliary software is “LED Studio Software”
H803SA 8 ports stand-alone DMX compatible RGB LED Strip Controller
- H803SA is a stand-alone RGB LED controller
- H803SA has 8 ports controlling maximum 8192 pixels, each port controls a maximum 1024 pixels
- SD card can store up to FAT32, FAT6 formats 64 DAT files programmed by LED Build software
- Many controllers can be synchronized with AC power supply
- H803SA can be connected to DMX console, you can switch file, adjust speed and brightness by DMX console
- Support encryption by limiting the number of power-on time
- H803SA supports below IC chips:
LPD6803, LPD8806, LPD6812, LPD6813, LPD1882, LPD1889, LPD1883, LPD1886, DMX512, HDMX, APA102, APA104, P9813, P9823, LD1510, LD1512, LD1530, LD1532, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, WS2801, WS2803, WS2811, DZ2809, SM16716, TLS3001, TLS3002, TM1812, TM1809, TM1804, TM1803, TM1914, TM1926, TM1829, TM1906, INK1003, BS0825, BS0815, BS0901, LY6620, DM412, DM413, DM114, DM115, DM13C, DM134, DM135, DM136, 74HC595, 6B595, MBI6023, MBI6024, MBI5001, MBI5168, MBI5016, MBI5026, MBI5027, TB62726, TB62706, ST2221A, ST2221C, XLT5026, ZQL9712, ZQL9712HV, etc.
H802TB DMX512 Compatible Offline Master LED Pixel Controller
- H802TB is a master controller that reads data from SD card to control multiple slave controllers
- Slave controllers are H801RA, H802RA and H801RC
- Two ports control maximum 64 slave controllers, drive maximum 40960 pixels
- H802TB can be connected to DMX console and occupies 3 channels, so you can switch files, adjust speed and brightness with DMX console
- You can set the address for DMX512 chips with H802TB
- Transmit data based on Ethernet protocol, nominal transmission distance is 100 meters
- SD card supports FAT32, FAT16 format, maximum capacity is 64G bytes, stores up to 64 DAT files
- Auxiliary software is “LED Build Software”
- Supported Driver Chips:
LPD6803, LPD8806, LPD6812, LPD6813, LPD1882, LPD1889, LPD1883, LPD1886, DMX512, HDMX, APA102, P9813, LD1510, LD1512, LD1530, LD1532, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, WS2801, WS2803, WS2811, WS2812, DZ2809, SM16716, TLS3001, TLS3002, TM1812, TM1809, TM1804, TM1803, TM1914, TM1926, TM1829, TM1906, INK1003, BS0825, BS0815, BS0901, LY6620, DM412, DM413, DM114, DM115, DM13C, DM134, DM135, DM136, 74HC595, 6B595, MBI6023, MBI6024, MBI5001, MBI5168, MBI5016, MBI5026, MBI5027, TB62726, TB62706, ST2221A, ST2221C, XLT5026, ZQL9712, ZQL9712HV, etc.
Note: H802TB can support more than the chips listed above(some chips have the same sequence diagram, for example: UCS512, WS2821 and DMX512 have the same protocol, H802TB supports them all).
H802RA Ethernet Art-Net protocol Slave Addressable LED Controller
- H802RA is a 4 ports output controller that employs Ethernet protocol and supports Art-Net protocol
- 4 ports control maximum 4096 pixels
- Support Art-Net protocol, so H802RA can work with MADRIX
- Address for the TM and UCS DMX512 driver chips, such as TM512, UCS512
- Configured as repeater or amplifier by LED Studio
- Work with master controller or computer
- Distance between two controllers is up to 100 meters
- Online software are LED Studio and Madrix
- Supported driver chips:
DMX512, HDMX, LPD6803, LPD8806, LPD1882, LPD1889, LPD1883, LPD1886, TM1812, TM1809, TM1804, TM1803, TM512, TM1926, TM1913, TM1914, TM1814, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, UCS512, UCS8904, APA102, APA104, P9813, WS2801, WS2803, WS2811, WS2812, WS2821, SM16716, SM16711, INK1003, LX1003, MY9221, MBI6021, MBI6024, LD1510, LD1512, LD1530, LD1532,etc
Request for More Information about Programmable LED Controller